Burrel solar panel guide and warnings

These instructions and warnings are for the Burrel chargeable solar panel (model: Burrel10K).

WARNINGS

• Do not connect the panel to a camera with incorrect input voltage. 
• When charging the panel, always make sure to connect the charger to correct input.
• Do not drop, disassemble or puncture the panel;
• Do not expose to fire, extreme temperature or submerge in water
• If you notice something not right when in use or when charging, like melting, a bulge in the housing or the unit gets extremely hot, stop using it immediately.
• Panel is meant to be used outside only.
• This solar charger is not a toy, keep away from children.

Failure to follow these safety instructions may result in fire, electric shock, damage, or other injury.

INTENDED USE

The Burrel chargeable solar panel supports all Burrel trail cameras with input of 6 Volt or 12 Volt. The solar panel can also be used with any other trail camera with compatible input voltages (6V, 9V or 12V).

PACKAGE CONTENTS

Unbox the solar panel and accessories from the box and make sure you have the following items:

1 x Trail camera solar panel

1 x USB-A to Type-C cable

1 x 4.0 x 1.7 to 4.0 x 1.7mm cable

1 x 3.5 x1.35 to 4.0 x 1.7mm cable

1 x 5.5 x 2.1 to 4.0 x 1.7mm cable

1 x Mounting bracket

1 x Mounting strap 

1 x Getting started guide

CHECKING THE INTERNAL BATTERY STATUS

Press on battery status found on the bottom of the solar panel. The LED-lights will illuminate to indicate the current charge of the internal battery:

CHARGING THE INTERNAL BATTERY

It is recommended to charge the panel battery before use with a standard USB charger. Panel battery can also be charged by placing the panel in direct sunlight.

Charging solar panel battery in sunlight: Tilt the pangel slightly upwards to face the sun. The green charge indicator LED is lit while charging. The indicator LED lights on the panel will start to flash when the panel is being charged. Please refer to the charge indication table below.

Charging on USB-C: You can charge the battery with standard USB-A charger (USB-A 5V DC/2A, charger not included).

Connect the included USB-A to USB-C cable to your charger and other end to the USB-C port of the solar panel. The indicator LED lights on the panel will start to flash when the panel is being charged. Please refer to the charge indication table below.

ATTACHING THE PANEL TO DIFFERENT SURFACES

You can attach the solar panel to different surfaces by using the include mounting bracket or mounting strap.

CONNECTING THE PANEL TO TRAIL CAMERA

1. Select the correct output cable that fits your trail camera model and connect it to the camera.
2. Plug the output cable to the correct output port on the solar panel. Make sure that the voltage printed next to the port corresponds to the voltage your camera uses. For Burrel cameras the voltage is either 6V or 12V depending on the camera mode (the correct voltage is printed on the bottom of the camera next to the camera input port).
3. The camera will now receive power from the internal battery of the solar panel. When the battery is drained the solar panel will automatically charge it when enough of sunlight is available.

Note! Never connect the solar panel to incorrect camera input. Always refer to your cameras manual to make sure what is the correct input voltage.

SPECIFICATIONS

Model: Burrel10K
Input voltage (DC): 5V/2A

Output voltage (DC): 12V/1.5A; 9V/2A; 6V/3A

Dimensions: 188mm x 157mm x 49mm

Battery capacity: 10 000 mAh

Working temperature: -20°C to 60°C

Dust/Waterproof rating: IP66

Charging time (charge by USB-C): 2 hours

Charging time (charge by DC 5V): 4 hours

Charging time (charge by sun light): approximately 20 hours

Manufacturing: manufactured in China for Natlink Oy (Takatie 6, 90440 Kempele Finland).

PRODUCT WARRANTY

Product has 12 month warranty which covers faulty materials and workmanship. This warranty is valid only when and proof or purchase is provided when doing a reclamation on the product. Seller or importer will either replace or repair the product free of charge within the warranty period. 

If the product has been opened the warranty will immediately terminate. The product is intended to be used with the accessories (cables, mounting brackets etc.) and if the product is used with other cables and mounts the products warranty is immediately terminated.

Warranty does not cover incorrect use of the product or damage caused to other products (trail camera). 

Note that warranty does not apply to normal wear of the product or to accidents or similar reasons outside of the control of the manufacturer (force majeure).